Since the launch of the first Bony Glove in 2008, we at 6aA have been working hard to bring the best possible gloves to our sport. Over the years, Bony has gone through several iterations, and in 2015 the Bony Glove Plus was launched, bringing together everything we’d learned from years of experience into a solid, well-tested design.
The BG+ is made using the highest-quality silicone available, with a carefully selected hardness that strikes a great balance between comfort and protection.
The glove is available in four sizes. You can use the two measurements shown in the diagram in the photo album as a guide to find the best fit. While the material will loosen slightly over time, it’s best not to exceed the listed measurements by more than 2–3 mm, especially in length (Measurement A). You’re aiming for a snug fit, but not an overly tight one. Hand shapes vary a lot, so while it’s not always easy to cater for everyone, we do our best to get as close as possible.
At the moment, we don’t offer left-handed gloves, but this is something we’re actively working on.
Please notice this product is sold in units.
Sizing Guidelines
Small: A180mm / B80mm
Medium: A190mm / B90mm
Large: A200mm / B93mm
Extra Large: A210mm / B95mm
To help prolong the life of your Bony, please follow the care and tips checklist below.
Care & Tips
- Dry your glove after every session to help prevent mould and fabric damage over time.
- Silicone doesn’t like the sun, so try not to leave your glove exposed for too long.
- To get the most life out of your Bony, repair any small damage as soon as you notice it using acetic-cure silicone. You can smooth it out with your fingertip and a bit of soapy water.
- If you see any silicone hanging off, don’t pull it. It’s better to trim it and then repair the area.
- We don’t recommend cutting out the palm of the glove, as this will drastically shorten its lifespan.
- Be gentle when putting on and taking off the glove to keep the wrist area in good shape. Doing this while the glove is wet makes it much easier.
Size:
Since the launch of the first Bony Glove in 2008, we at 6aA have been working hard to bring the best possible gloves to our sport. Over the years, Bony has gone through several iterations, and in 2015 the Bony Glove Plus was launched, bringing together everything we’d learned from years of experience into a solid, well-tested design.
The BG+ is made using the highest-quality silicone available, with a carefully selected hardness that strikes a great balance between comfort and protection.
The glove is available in four sizes. You can use the two measurements shown in the diagram in the photo album as a guide to find the best fit. While the material will loosen slightly over time, it’s best not to exceed the listed measurements by more than 2–3 mm, especially in length (Measurement A). You’re aiming for a snug fit, but not an overly tight one. Hand shapes vary a lot, so while it’s not always easy to cater for everyone, we do our best to get as close as possible.
At the moment, we don’t offer left-handed gloves, but this is something we’re actively working on.
Please notice this product is sold in units.
Sizing Guidelines
Small: A180mm / B80mm
Medium: A190mm / B90mm
Large: A200mm / B93mm
Extra Large: A210mm / B95mm
To help prolong the life of your Bony, please follow the care and tips checklist below.
Care & Tips
- Dry your glove after every session to help prevent mould and fabric damage over time.
- Silicone doesn’t like the sun, so try not to leave your glove exposed for too long.
- To get the most life out of your Bony, repair any small damage as soon as you notice it using acetic-cure silicone. You can smooth it out with your fingertip and a bit of soapy water.
- If you see any silicone hanging off, don’t pull it. It’s better to trim it and then repair the area.
- We don’t recommend cutting out the palm of the glove, as this will drastically shorten its lifespan.
- Be gentle when putting on and taking off the glove to keep the wrist area in good shape. Doing this while the glove is wet makes it much easier.
6aA is a small business and most of our gear is handmade in small batches so sometimes we could run out of stock of some products. If that is the case, please let us know your name, email and which products are you looking to purchase and we will put you on waiting list and contact you to finalise details.
The timeframe to restock most of our in-house made items is 2 to 3 weeks depending on demand. Thanks for your patience and your support!
Image 1 of 6
Image 2 of 6
Image 3 of 6
Image 4 of 6
Image 5 of 6
Image 6 of 6